Levolor blinds are a stylish and durable way to cover your windows, but they can also get damaged, dirty, or outdated over time. If you want to remove some slats from your Levolor blinds for cleaning, repairing, or shortening, you might wonder how to do it without ruining the blinds or the cords. But don’t worry, you can remove slats from Levolor blinds with some simple steps and tools. Here’s how to do it step by step.
Removing slats from Levolor blinds involves removing the plugs from the bottom rail, cutting the ladders below the desired length, and sliding out the unwanted slats.
Step 1: Mark the desired length
- The first thing you need to do is mark the desired length of your Levolor blinds.
- You need to lower the blinds fully and measure how much you want to shorten them.
- You need to add two extra slats to the length you want, as these will be used to secure the bottom rail.
- You need to mark the slat that will be your new bottom slat with a pencil or a piece of tape.
Step 2: Remove the plugs from the bottom rail
- The next thing you need to do is remove the plugs from the bottom rail of your Levolor blinds.
- You need to lift the blinds up and locate the plugs under the bottom rail. There should be two or more plugs depending on the width of your blinds.
- You need to use a flathead screwdriver or a similar tool to pry out the plugs and expose the cords and ladders underneath.
- You need to be careful not to damage or cut the cords that raise and lower the blinds.
Step 3: Cut the ladders below the desired length
- The third thing you need to do is cut the ladders below the desired length of your Levolor blinds.
- You need to use scissors or a knife to carefully cut the horizontal ladders below the marked slat that will be your new bottom slat.
- You need to leave about an inch of ladder below the marked slat for tucking into the bottom rail later.
- You need to repeat this for all the ladders across your blinds.
Step 4: Slide out the unwanted slats
- The fourth thing you need to do is slide out the unwanted slats from your Levolor blinds.
- You need to hold the marked slat with one hand and gently pull out the slat below it with another hand.
- You need to repeat this for all the slats below the marked slat until you reach the original bottom slat.
- You need to discard or save the removed slats for future use.
Step 5: Reattach the bottom rail
- The last thing you need to do is reattach the bottom rail to your Levolor blinds.
- You need to tuck in the ends of the ladders into the holes on the bottom rail where you removed the plugs.
- You need to trim any excess ladder with scissors or a knife if needed.
- You need to replace the plugs into the holes and snap them into place.
FAQs
Q: How do I reinstall Levolor blinds after removing slats? A: To reinstall Levolor blinds after removing slats, you need to reverse the steps above. You need to attach the brackets to the window frame or wall, slide in the headrail of the blinds into the brackets, and lock them into place. Then you need to adjust the height and tilt of the slats as desired.
Q: How do I clean Levolor blinds after removing slats? A: To clean Levolor blinds after removing slats, you can either dust them with a soft cloth or a vacuum cleaner attachment, or wash them in a bathtub or a sink with mild soap and water. Avoid using harsh chemicals or abrasives that might damage or discolor the blinds.
Wrap Up
Levolor blinds are a great way to decorate your windows with style and functionality. But they can also get damaged, dirty, or outdated over time. You don’t have to replace them if you want to remove some slats from them. You can remove slats from Levolor blinds with some simple steps and tools. To remove slats from Levolor blinds, you just need to mark the desired length, remove the plugs from the bottom rail, cut the ladders below the desired length, slide out the unwanted slats, and reattach the bottom rail. Then you can enjoy your new and improved Levolor blinds.
