Honeycomb blinds are a type of window covering that have a cellular structure that traps air inside each cell, creating a layer of insulation that helps regulate the temperature in your room. They are also known as cellular shades, and they can come in various styles, such as corded, cordless, top-down/bottom-up, or motorized.
However, like any other type of blinds, honeycomb blinds can get damaged over time. One of the most common problems that honeycomb blinds face is broken or tangled strings. If the strings of your honeycomb blinds snap or get stuck, you won’t be able to raise or lower your blinds properly.
Fortunately, restringing honeycomb blinds is not very difficult, and you can do it yourself with some basic tools and skills. In this guide, we will show you how to restring honeycomb blinds in a few simple steps.
1 Remove the blinds from the window and lay them flat on a clean surface.
2 Remove the bottom rail and the end caps from the headrail of the blinds.
3 Pull out the old strings from the blinds and discard them.
4 Cut new strings according to a formula based on the size of your blinds.
5 Thread the new strings through the fabric cells and the headrail using a restring needle or a wire tool.
6 Tie the new strings to the bottom rail and reattach it to the blinds.
7 Reinstall the end caps and the blinds in the window.
Step-by-Step Instructions
Here are the detailed instructions on how to restring honeycomb blinds:
- Remove the blinds from the window by loosening the screws on the brackets and rotating the headrail toward you. Be careful not to damage the brackets or the window frame.
- Lay the blinds flat on a clean surface, such as a table or a floor. Make sure you have enough space to work on them.
- Remove the bottom rail from the blinds by sliding it off from one end. You may need to use a flat-head screwdriver to pry it open if it is tight.
- Remove the end caps from the headrail of the blinds by popping them off with a flat-head screwdriver. You should see two cords coming out of each end cap. These are the lift cords that control the movement of your blinds.
- Pull out the old strings from the blinds and discard them. You may need to use a pair of scissors or pliers to cut or untie any knots or tangles.
- Use a formula to determine the amount of new string you need for your repair. The formula is: (height of blind x 2) + (width of blind) + 12 inches = length of string per cord. For example, if your blind is 60 inches high and 36 inches wide, you need (60 x 2) + 36 + 12 = 168 inches of string per cord. You will need two cords for each side of your blind, so multiply this number by four to get the total amount of string you need.
- Cut four pieces of new string according to your calculation. Use a high-quality polyester string that is suitable for honeycomb blinds. You can order replacement string online or from your local hardware store.
- Thread one end of each string through a restring needle or a wire tool. A restring needle is a long metal needle with an eye at one end and a hook at the other. A wire tool is a flexible wire with loops at both ends.
- Feed one string through each fabric cell on one side of your blind using your restring needle or wire tool. Start from the bottom cell and work your way up to the top cell. Make sure to keep some slack in each string as you go along.
- Feed each string through its corresponding hole in the headrail using your restring needle or wire tool. You should see four holes on each side of your headrail where the old strings came out.
- Tie each string to its corresponding lift cord using a double knot. Make sure to tie them securely and evenly so that your blind will operate smoothly.
- Slide the bottom rail back onto the blind and make sure it fits snugly.
- Repeat steps 8 to 12 for the other side of your blind.
- Reattach the end caps to the headrail by snapping them back into place.
- Reinstall the blinds in the window by aligning them with the brackets and rotating the headrail until it locks into place. Tighten the screws on the brackets if needed.
- Test your blinds by raising and lowering them with the lift cords. Adjust the tension of the strings if needed by loosening or tightening the knots.
Tips on How to Maintain Honeycomb Blinds
To keep your honeycomb blinds working properly and looking their best, follow these tips on how to maintain them:
- Dust your honeycomb blinds regularly with a feather duster, a vacuum cleaner with a soft brush attachment, or a hair dryer on low heat. This will prevent dust from accumulating and affecting their performance.
- Avoid using harsh chemicals or abrasive materials that may damage the fabric or structure of your blinds. Use only mild detergents or water-based solutions for cleaning.
- Do not expose your honeycomb blinds to excessive moisture or humidity, as this may cause warping, fading, or mold growth. If your blinds get wet, dry them as soon as possible with a clean cloth.
- Do not force or twist your lift cords, as this may damage the strings or the mechanism inside. Use gentle motions and avoid applying too much pressure.
- Repair any loose or broken strings, slats, cords, or hardware as soon as possible to prevent further damage or injury. Contact the manufacturer or a professional for assistance if needed.
Conclusion
Honeycomb blinds are a beautiful and functional addition to any home, but they can also get damaged over time. One of the most common problems that honeycomb blinds face is broken or tangled strings.
In this guide, we showed you how to restring honeycomb blinds in a few simple steps.
If you have any questions or need more help, feel free to contact us at Huetifulhomes.com. We are always happy to assist you with your home decor needs.