If your valance curtains are looking a little shabby, don’t worry – you can fix them yourself with some simple tools and techniques. In this post, I’ll show you how to fix valance curtains in three different ways: by cutting and hemming them, by attaching them with clips or rings, and by hanging them with hooks.
How do you fix valance curtains?
You can fix valance curtains by cutting and hemming them to adjust their length and shape, by attaching them to the curtain rod with clips or rings to secure them in place, or by hanging them from the wall or ceiling with hooks to create a different look.
How to fix valance curtains by cutting and hemming them
If your valance curtains are too long or too wide for your window, or if they have frayed or torn edges, you can fix them by cutting and hemming them to fit your window and give them a neat finish. Here’s how to do it:
- Get the right tools. You’ll need a straight edge, a measuring tape, a pencil, scissors, an iron, an ironing board, pins, needle and thread or a sewing machine.
- Remove the valance curtains from the rod and lay them flat on the floor or a large table.
- Measure the width and length of your window and decide how much you want to cut off from your valance curtains. You can either match the width of your window or make it slightly wider for more fullness. You can also choose how much of your window you want to cover with your valance curtains – typically between 2 to 6 inches (5 to 15 cm).
- Mark the spots where you want to cut your valance curtains with a pencil using the straight edge and measuring tape. Make sure to mark both sides of the fabric and leave some extra fabric for hemming – about 1 inch (2.5 cm) for each side.
- Cut your valance curtains along the marked lines with scissors. Be careful not to cut too much or too little.
- Fold and press the edges of your valance curtains with an iron on low heat to create a hem. Pin the hem in place with pins.
- Sew the hem with needle and thread or a sewing machine using a straight stitch. Remove the pins as you sew.
- Hang your valance curtains back on the rod and adjust them as needed.
How to fix valance curtains by attaching them with clips or rings
If your valance curtains are sliding off the rod or sagging in the middle, you can fix them by attaching them to the rod with clips or rings. Clips or rings are metal or plastic devices that clip onto the fabric of your valance curtains and slide onto the rod. They can help keep your valance curtains in place and create a more uniform look. Here’s how to do it:
- Get the right tools. You’ll need clips or rings that match your curtain rod and your valance curtains. You can find clips or rings in most home improvement stores or online.
- Remove the valance curtains from the rod and lay them flat on the floor or a large table.
- Attach one clip or ring to each end of your valance curtains by clipping it onto the top edge of the fabric. Make sure they are aligned with each other and not too close to the edge.
- Attach more clips or rings along the top edge of your valance curtains at equal intervals. The number of clips or rings you need depends on how wide your curtain rod is and how much space you want between each panel. A general rule of thumb is to use one clip or ring for every 6 to 8 inches (15 to 20 cm) of curtain width.
- Hang your valance curtains back on the rod by sliding the clips or rings onto it. Adjust them as needed.
How to fix valance curtains by hanging them with hooks
If you want to change the look of your valance curtains or create more height for your window, you can try hanging them with hooks instead of using a rod. Hooks are metal or plastic devices that are attached to the wall or ceiling and hold the fabric of your valance curtains. They can create a more dramatic and elegant look for your window, as well as hide the curtain rod or hardware. Here’s how to do it:
- Get the right tools. You’ll need hooks that match your wall or ceiling color and your valance curtains. You can find hooks in most home improvement stores or online.
- Remove the valance curtains from the rod and lay them flat on the floor or a large table.
- Measure the width and height of your window and decide how many hooks you want to use and where you want to place them. You can either use one hook for each corner of your window or use more hooks to create a swag or scallop effect. You can also choose how high you want to hang your valance curtains – typically between 2 to 6 inches (5 to 15 cm) above your window frame.
- Mark the spots where you want to attach your hooks on the wall or ceiling with a pencil using the measuring tape. Make sure they are evenly spaced and aligned with each other.
- Attach your hooks to the wall or ceiling by following the instructions on the package. You may need to drill holes, use screws, or use adhesive depending on the type of hooks you use.
- Hang your valance curtains from the hooks by draping the fabric over them. Adjust them as needed.
FAQs
How do you hang a valance over curtains?
To hang a valance over curtains, you can use one of these methods:
- Use a double curtain rod that has two rods attached to one set of brackets. Hang your curtains on the lower rod and your valance on the upper rod.
- Use two single curtain rods that are installed separately on the wall or window frame. Hang your curtains on the lower rod and your valance on the upper rod.
- Use a valance rod that is designed to fit over an existing curtain rod. Hang your curtains on the regular rod and your valance on the valance rod.
How do you make a valance curtain?
To make a valance curtain, you can follow these steps:
- Choose a fabric that matches or complements your curtains and your room decor. You can use any type of fabric, such as cotton, linen, silk, or polyester.
- Measure the width and length of your window and decide how big you want your valance curtain to be. You can either match the width of your window or make it slightly wider for more fullness. You can also choose how much of your window you want to cover with your valance curtain – typically between 2 to 6 inches (5 to 15 cm).
- Cut your fabric according to your measurements, leaving some extra fabric for hemming – about 1 inch (2.5 cm) for each side.
- Fold and press the edges of your fabric with an iron on low heat to create a hem. Pin the hem in place with pins.
- Sew the hem with needle and thread or a sewing machine using a straight stitch. Remove the pins as you sew.
- Hang your valance curtain on a rod, clips, rings, or hooks.
How do you fix a sagging valance?
To fix a sagging valance, you can try these tips:
- Use more clips, rings, or hooks to support the weight of the fabric and prevent sagging.
- Use a stiffer or heavier fabric for your valance that will hold its shape better and resist sagging.
- Use interfacing or batting to add some structure and thickness to your valance fabric and prevent sagging.
- Use pleats, gathers, or folds to create some volume and fullness for your valance and prevent sagging.
Wrap Up
Valance curtains are a great way to add some style and charm to your windows, but they can also get damaged or worn out over time. If your valance curtains are looking a little shabby, don’t worry – you can fix them yourself with some simple tools and techniques. Whether you choose to cut and hem them, attach them with clips or rings, or hang them with hooks, you can fix your valance curtains and give them a new lease of life. I hope this post helped you learn how to fix valance curtains. If you have any questions or comments, feel free to leave them below. Happy DIYing!
Dale is the colorful mind behind HuetifulHomes.com, where he shows you how to create a home that is as fun and fabulous as you are. He has a passion for color and a knack for DIY, with years of interior design experience he shares his tips and tricks on how to create a home that reflects your personality and style. He believes that color is the key to happiness, and he wants to help you make your home more Huetiful.
